ATADAPCAN01【PDF 3/6 页】EXTENSION CAN ADD-ON TO STK500/1

您好，
买卖IC网欢迎您。
请登录
免费注册

Sheet目录1196

1页 2页 [3页]4页 5页 6页

CAN Bus Interface

BUS Connectors

Several options are available to physically connect the ATADAPCAN01 to a CAN bus.

The D-SUB-9 MALE connector is the primary connection point to a CAN bus. Alterna-

tively, the 10-pin header labelled "CAN BUS flat-cable" can be used, or both connectors

can be used if the CAN bus topology requires it. Both connectors are wired according to

CiA Draft Standard 102 version 2.0 as shown in table 1.

Table 1. CAN Bus Connector Wiring

Signal Description

Reserved

CAN_L

CAN_GND

Reserved

CAN_SHLD*

CAN_GND

CAN_H

Reserved

CAN_V+

(not used)

D-SUB-9 pin

1

2

3

4

5 (1)

6

7

8

9

Flat-cable Pin

1

3

5

7

9 (1)

2

4

6

8

10

Note:

1. CAN_SHLD pins are not connected together internally

CAN BUS Grounding and The "CAN_SHLD" signal in each of the two CAN bus connectors can be optionally con-

Shielding

CAN BUS Termination

nected to ground by mounting 0 ohm or small value resistors in positions R2 (for D-SUB-

9) and R3 (for flat-cable). The landing pads of both R2 and R3 are 1206 standard size.

By default, the "CAN_GND" signals in both connectors are wired to the STK500 ground

through 0 ohm resistor R1. Removing R1 will isolate the "CAN_GND" ground signals on

the CAN bus from the STK500 / ATADAPCAN01 ground.

To function correctly, a CAN bus requires 120 ohm termination on both ends. The

ATADAPCAN01 can become a terminated node on the CAN bus simply by setting the

jumper labelled "TERM". This terminates the CAN bus with two series-connected 62

ohm resistors. Setting the jumper labelled "SPLIT" connects the centre-tap between

these two resistors to ground through 10nF capacitor C1. This reduces common-mode

noise on the bus line. This centre tap can also be stabilised as described later in the

”Split voltage” section (if supported by the CAN transceiver mounted in "CAN1").

CAN Transceiver Options The ATADAPCAN01 board has two CAN transceiver footprints. This is to facilitate easy

evaluation of alternate CAN devices as well as to provide access to various extra fea-

tures of some of these parts. Refer to the schematic diagram in Figure 2 (below) while

considering these options.

Both "CAN1" and "CAN2" footprints use standard CAN device pinouts for pins 1, 2, 3, 4,

6 and 7. By default, "CAN1" is mounted on the board (Atmel ATA6660). To use a device

in "CAN2", solder the device to the board, and remove the 0 ohm ’resistors’ labelled R8,

R9 R10 from the "CAN1" section, and mount them into the "CAN2" section in positions

R11, R12, R13. Although it is acceptable that idle CAN transceivers remain attached to

the CAN bus, only one CAN device should be connected to the AVR device at any time.

3

AT90CAN128

4330B–CAN–03/04

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

ATAVRBC100 REF DESIGN KIT BATTERY CHARGER

ATAVRDB101 MODULE DISPLAY LCD/RGB BACKLIGHT

ATAVRMC100 KIT EVALUATION FOR AT90PWM3

ATAVRMC200 KIT EVAL FOR AT90PWM3 ASYNC

ATAVRMC300 BOARD EVAL LV MOTOR CONTROL PWR

ATAVRMC303 BOARD EVAL MOTOR CTRL W/XMEGA

ATAVRMC320 KIT EVAL MOTOR CTRL CAN/LIN

ATAVRSB100 SMART BATTERY DEVELOPMENT KIT

相关代理商/技术参数

ATADAPMEGA162 功能描述:子卡和OEM板 ADAPTER FOR ICE50 MEGA-ATMEGA8515/162 RoHS:否制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit

ATADAPMEGA169 功能描述:ADAPTER PERSON ICE50 ATMEGA169 RoHS:否类别:编程器，开发系统 >> 过时/停产零件编号系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口）所含物品:面板、缆线、软件、数据表和用户手册其它名称:520-1035

ATADAPMEGA32 功能描述:子卡和OEM板 ADAPTER F/ICE50 MEGA ATMEGA8535/16/32 RoHS:否制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit

ATADAPMEGA8 功能描述:子卡和OEM板 ADAPTER FOR ICE50 MEGA - ATMEGA8 PDIP RoHS:否制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit

ATADAPT2313 功能描述:子卡和OEM板 ADAPTER FOR ICE50 TINY2313 RoHS:否制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit

ATADAPTCAN01 制造商:Atmel Corporation 功能描述:STK501 CANN ADD-ON - Bulk

ATADAPTEST 功能描述:子卡和OEM板 ADAPTER FOR ICE50 TEST RoHS:否制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit

ATADAPTINY13 功能描述:子卡和OEM板 ADAPTER FOR ICE50 TINY13IP RoHS:否制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit